平台合作
相关推荐
数据表中记载的“Energy Sharing control Operation Example”示意图只适用于室温吗？
不是，在动作温度范围内均适用
您好，我们在评估MLX90632，这个控制寄存器REG_CONTROL，这个对应的测量功能的使能是需要事实控制的吗？
你好，如果你软件上使用了example例程的话，我们在自己的main里一直调用start measure函数就OK了，这个函数会负责对control寄存器进行控制
Is it possible to update (Self-programming) the firmware that runs on the microcontroller ? For example, I am thinking of receiving data from communication and updating it.
It is possible. The ML62Q1000 series has a self-programming function. For details, refer to "25.3 Self-Programming" in the "ML62Q1000 Series User's Manual". An IAP (In-Application Programming) sample program is provided as a usage example. The IAP sample program is included in the ML62Q1000 series reference software and can be downloaded from the support contents of ML62Q1000 series of our product site.
Energy Sharing功能是指？
是指为了抑制IC的温度上升，将总热量分散在外部电阻和LED驱动IC上的机能。因为可以抑制IC的温度上升，所以可以实现对IC动作温度补偿进行设计。
Can ML7344 be used in 12.5 kHz band operation?
The transmission is possible depending on the frequency deviation. However, because the receiving bandwidth of the LSI is fixed to 25 kHz, the adjacent channel selectivity and the intermodulation characteristics in 12.5 kHz operation cannot meet the requirement. Related Products: ML7344 family
The following error occurred after an attempt to connect a debugger using on-chip emulator: “ICE error: 6307H Failed to start on-chip ICE block.” What should I do?
The ICE error: 6307H is caused by the following situations. (1) Poor connection between the on-chip emulator and microcontroller. (2) Microcontroller failure. (3) For the microcontroller on which the test pin and general-purpose port are shared, output port is set by a program. An error caused by (1) can be avoided by connecting the on-chip emulator and microcontroller properly. For a reference board, check that jumpers are set on the on-chip emulator side. When there is no problem with connection, (2) or (3) may be the case. Replace the target LSI.
Does the A/D converter include a sample/hold circuit? Or, does a hold occur for the number of input ports?
The ADC of our microcontroller includes a sample/hold circuit. Note that the sample/hold circuits for the number of input ports are not provided.
For BD3812F, What is the polarity of the MUTE terminal?
The "control signal" listed on page 3 of the datasheet is the specification for the MUTE pin. MUTE is OFF at "H" level, and MUTE is ON at "L" level.
When performing A/D conversion for multiple channels, are channels put into the sampling wait state until sampling of one channel is completed? Or, can sampling be performed simultaneously?
The ADC of our microcontroller performs A/D conversion while switching channels and therefore unprocessed channels are put into the wait state. Simultaneous conversion cannot be performed.
After setting the register value of [PA_ADJ1 to 3] register (B1 0x04-0x06), [PA_REG_ADJ1 to 3] register (B1 0x33-0x35), [PA_REG_FINE_ADJ] register (B1 0x13) through adjusting PA of ML7396, how long does it take for them to be reflected in the wireless output?
After completion of register settings, the control signal is sent to the PA without time lags. Therefore, the time taken for them to be reflected is almost equivalent to the response time of PA. Since PA provides quick response, they are reflected within 100 us. Related Products: ML7396 family
Can we modify threshold values easily?
Customers can save threshold values in the external EEPROM and control their systems with this threshold values. Please refer to each documents.
求推荐封装为SOT23-6的同步整流控制芯片，VCC电压要能承受25V以上！
推荐采用ROHM的同步整流控制芯片BM1R00146F，其Vcc电压最高可承受32V，但封装为SOP8，参考链接：High Efficiency and Low Standby Power,CCM corresponding Secondary Side Synchronous Rectification Controller IC BM1R00146F BM1R00147F BM1R00148F BM1R00149F BM1R00150F Datasheet
对于贴片式电阻器的焊接条件有哪些建议？
"Soldering conditions : Resistrors"请参阅。这是以使用无铅焊膏(Sn-3Ag-0.5Cu)为基础的条件下提出来的。建议不要将射流焊接法、手工焊接法用于超小型贴片电阻器(0603规格尺寸)、贴片排阻器(1005×2、×4、1608×2、×4、×8)。这是因为相邻电极间有可能发生焊料跨接。实际使用时应该利用用户的设备、安装的电路板仔细进行检验。
What is the recommended microcontroller? Can we use third party microcontroller?
LAPIS recommend ML610Q486P, ML610Q488P, ML610Q112 for analog-front end type LSIs. Customer can use third party microcontroller.
In the FSK mode, when continuously transmitting the modulated wave using RF_TEST_MODE, the center frequency shifts by about 3 KHz.
As described in the data sheet, when using RF_TEST_MODE in FSK mode, the modulator reads unnecessary data before the generation of the expected test data just after TX_ON is started up. Therefore, the center frequency changes. To use RF_TEST_MODE correctly, check again through the following procedure. 1. Initialization register setting 2. Execute VCO_CAL 3. TX_ON 4. After starting up TX, MODEM reset * Note: Usually, this event does not occur when transmitting packets containing DIO control. So, it is not required to perform a MODEM reset after TX_ON. This is also an event specific to FSK mode. There is no problem in GFSK mode. Related Products: ML7344/ML7406 family, ML7345 family, ML7404, ML7414
电子商城
现货市场
服务
提供蓝牙BLE芯片协议、蓝牙模块、蓝牙成品测试认证服务；测试内容分Host主机层，Controller控制器层，Profile应用层测试。支持到场/视频直播测试，资深专家全程指导。
实验室地址： 深圳 提交需求>
授权代理品牌：集成电路
授权代理品牌：分立元件
授权代理品牌：接插件及结构件
授权代理品牌：部件、组件及配件
授权代理品牌：电源及模块
授权代理品牌：电子材料
授权代理品牌：仪器仪表及测试配组件
授权代理品牌：电工工具及材料
授权代理品牌：机械电子元件
授权代理品牌：加工与定制
我要提问