平台合作
相关推荐
想了解电阻器的型号构成说明。
请参考电阻器的型号构成说明。https://fscdn.rohm.com/en/products/databook/explanation/passive/resistor/common/description.pdf
想了解晶体管的型号构成说明。
请参考晶体管型号构成说明。https://fscdn.rohm.com/en/products/databook/explanation/discrete/transistor/common/transistorkousei.pdf
想了解二极管的型号构成说明。
请参考二极管的型号构成说明。https://fscdn.rohm.com/en/products/databook/explanation/discrete/diode/common/diodekousei.pdf
想了解LED的型号构成说明。
It is available on the Design Resources of the LED Product pages.（https://www.rohm.com.cn/products/led）
想了解IPM的型号构成说明。
请参考相应产品的数据表。
激光二极管的焊接条件？
请参考激光二极管在使用上的注意事项。（https://fscdn.rohm.com/en/products/databook/applinote/opto/laser-diodes/precautions_for_ld_an-e.pdf）
推荐一款LM2575的LDO的替代料？
推荐ROHM的电源芯片BD90620HFP-C（该芯片为可调，宽输入电压），资料：https://rohmfs-rohm-com-cn.oss-cn-shanghai.aliyuncs.com/en/products/databook/datasheet/ic/power/switching_regulator/bd906xxefj-c-e.pdf。
Can I write data on 0000H to 0FFFH of the FLASH data area Segment A?
Reading is possible but not writing. Segment A is the mirror area of Segment 2. If data are written on Segment 2, they can be also read from Segment A. Related Products: ML610(Q)40x, ML610(Q)42x, ML610(Q)47x, ML610(Q)48x, ML610Q10x, ML610Q11x, ML610Q17x, ML610Q30x, ML610Q35x, ML610Q38x, ML610Q41x, ML610Q43x, ML610Q46x, ML620Q13x, ML620Q15x, ML620Q416/ML620Q418, ML620Q503H/ML620Q504H/ML620Q506H, ML62Q12xx, ML62Q13xx, ML62Q14xx, ML62Q15xx/ML62Q18xx, ML62Q16xx, ML62Q17xx
There is the silence insertion function on edit ROM function. Do we need to prepare the individual "silent" phrase?
The individual "silent" phrase is not necessary. The silent data ROM size can be reduced using the silence insertion function. Related Products: ML22420/460, ML22530/Q53x, ML2256x/Q563, ML2257x/Q573, ML22594, ML22660/Q66x, ML2272x/76x, ML2282x/86x, ML22Q374/Q394, ML22Q553
Is there any way to avoid receiving data during CCA?
To prevent data reception during CCA, follow the steps shown below. To restore data reception after CCA, be sure to return to the original setting before reception. [Procedure] (1) Setting to prevent bit synchronization from being established BANK1: 0x5C = 0x00 BANK3: 0x03 = 0x00 (2) CCA started (3) Waiting for CCA completion (4) After completion of CCA, TRX_OFF (1) Setting to establish bit synchronization BANK1: 0x5C = original value BANK3: 0x03 = original value Related Products: ML7345 family
Is it possible to generate a ROM code data file with HTU8, and write to flash ROM to evaluate without acquiring a ROM code number?
Yes. It is possible to generate a ROM code data file with HTU8, and write to flash ROM to evaluate without acquiring a ROM code number. The content itself on the ROM code data file output by HTU8 is not related to a ROM code number. Related Products: ML610(Q)40x, ML610(Q)42x, ML610(Q)47x, ML610(Q)48x, ML610Q10x, ML610Q11x, ML610Q17x, ML610Q30x, ML610Q35x, ML610Q38x, ML610Q41x, ML610Q43x, ML610Q46x, ML620Q13x, ML620Q15x, ML620Q416/ML620Q418, ML620Q503H/ML620Q504H/ML620Q506H, ML62Q12xx, ML62Q13xx, ML62Q14xx, ML62Q15xx/ML62Q18xx, ML62Q16xx, ML62Q17xx
Is there any way to avoid receiving data during CCA?
To prevent data reception during CCA, follow the steps shown below. To restore data reception after CCA, be sure to return to the original setting before reception. [Procedure] (1) Setting to prevent bit synchronization from being established BANK2: 0x03 = 0x00 BANK2: 0x0E = 0x00 (2) CCA started (3) Waiting for CCA completion (4) After completion of CCA, TRX_OFF (1) Setting to establish bit synchronization BANK2: 0x03 = original value BANK2: 0x0E = original value Related Products: ML7396 family
关于线性稳压器， 如果Datasheet中没有输出电容器最大电容值描述，是否可以无限制使用？
加大输出电容器的电容，虽然稳定性会有所改善，但是需要注意其他特性。加大电容将会延长ON时的充电时间、OFF时的放电时间，将电源电压设为OFF时，输出和输出的电压就会反向，从而有可能会有大电流向IC逆流。使用大容量时，请考虑使用逆流旁路二极管及防逆流二极管。
Does the port enter a high-impedance output state when it is set to the high-impedance output mode regardless of a value of the port data register (PnD)?
Yes. The port enters the high-impedance output state. Related Products: ML610(Q)40x, ML610(Q)42x, ML610(Q)47x, ML610(Q)48x, ML610Q10x, ML610Q11x, ML610Q17x, ML610Q30x, ML610Q35x, ML610Q36x, ML610Q38x, ML610Q41x, ML610Q43x, ML610Q46x, ML620Q13x, ML620Q15x, ML620Q416/ML620Q418, ML620Q503H/ML620Q504H/ML620Q506H, ML62Q12xx, ML62Q13xx, ML62Q14xx, ML62Q15xx/ML62Q18xx, ML62Q16xx, ML62Q17xx
运算放大器产生输入偏置电流的原因。另外，请告知最大条件（温度及电源电压）。
输入偏置电流在双极型产品和CMOS产品中不同。双极型产品的输入偏置电流取决于输入段晶体管的基极电流和内部电流源，由于温度及电源电压，hFE受影响，输入偏置电流发生变化。在CMOS产品中，分别连接在输入端子和VDD之间、输入端子和VSS之间的静电保护元件漏电流流出和流入之差就是输入偏置电流，由于保护元件的漏失受温度及电源电压的影响而发生变化，因此该差分也会随之变化，从而导致输入偏置电流变化。详情请参考技术资料。温度及电源电压依赖性因各产品的电路结构而异，因此请确认Datasheet图及标准值。
电子商城
现货市场
授权代理品牌：集成电路
授权代理品牌：分立元件
授权代理品牌：接插件及结构件
授权代理品牌：部件、组件及配件
授权代理品牌：电源及模块
授权代理品牌：电子材料
授权代理品牌：仪器仪表及测试配组件
授权代理品牌：电工工具及材料
授权代理品牌：机械电子元件
授权代理品牌：加工与定制
我要提问