Grid And System Protection NA003-M64 from TELE Meets Belgian Standard C10-11

时间： 2023-09-09 来源：TELE News

技术问答

With more and more renewable energy feeders the grid is becoming more unstable and the standards for components are constantly changing. The new C10-11 standard of the energy supplier Belgium as well as the European standard EN50549 require zero voltage detection and activation of a narrower frequency window in the event of a fault. This is intended to detect faults and short circuits in the higher-level medium-voltage network so that the network can be stabilized in good time. In order for devices for safe network separation to be able to do this, they must be able to calculate the so-called zero voltage or zero sequence. The NA003-M64 from TELE Haase now has this function integrated and is thus fit for international use.

What exactly is this zero voltage?

In systems for generating renewable energy, such as photovoltaic or small wind turbines, 230 volts are usually applied to each phase in 3-phase networks and the phase angle of each phase is 120 degrees. In this ideal grid condition, the zero sequence is 0 volts. However, if a fault occurs, such as a short circuit in the higher-level supply network, one or more phase voltages and the associated phase angles change, resulting in a zero offset (= Zero Voltage or Zero Sequence).

The Belgian C10-11 as well as the European standard EN50549 require that the grid and system protection must disconnect the generation grid from the main grid if the Zero Voltage becomes greater than 20 percent of the nominal voltage.

Mathematics and programming as a challenge

The TELE developer team developed a completely new algorithm for this task, which calculates the Zero Sequence from the shift of the three measured phase voltages and the three phase angles. On the one hand, the challenge was the mathematical implementation of the trigonometric functions; on the other hand, the algorithm had to be designed in such a slim way that it could fit on the existing limited memory space of the controller in the NA003-M64.

Two software engineers and an integration tester designed the architecture of the new calculation method, converted it to C code, and integrated it into the NA003-M64’s existing software. The project took nine months and was completed internally. Afterward, the certification process with a German testing institute was started and successfully completed. TELE’s grid and system protection now provides a total of 46 parameter sets for thirteen different countries.

Advantages of the solution

By integrating the calculation of the Zero Voltage into the existing software of the TELE grid and system protection, it is possible to set at which shift in the 3-phase network a network disconnection between the power generator and the main network should occur. With a further (much lower) threshold value for the Zero Voltage, activation of a narrower frequency window 49.7Hz to 50.3Hz (normally 47.5Hz to 51.5Hz) can take place with an already very small shift in the 3-phase network. This means that the Zero Voltage also has an indirect influence on other measured variables, in this case, frequency detection.

Zero Voltage calculation is universally applicable

The calculation model developed in-house for zero voltage can be used universally. For example, the changeover to the new model is also being prepared for the development of the new TELE Performance Sensor eCap.

发送到邮箱 |
+1 赞 0
收藏
评论 0
| 转发至：

本文由翊翊所思转载自TELE News，原文标题为:Grid and system protection from TELE meets Belgian standard C10-11，本站所有转载文章系出于传递更多信息之目的，且明确注明来源，不希望被转载的媒体或个人可与我们联系，我们将立即进行删除处理。

全部评论（0）

暂无评论

SLKOR SL44E-9 High-performance Hall Sensor with a Working Voltage of up to 60V and IDD Current of 40mA

The SL44E-9 can withstand a working voltage of up to 60V, allowing it to operate stably under a wider range of power conditions, such as high-voltage grid monitoring, electric vehicle charging stations, or other high-voltage applications. Its static current of 40mA balances power consumption and performance requirements.

产品发布时间 : 2023-11-27

【产品】采用伽马工业设计的通用电表eCap，整体宽度45毫米/1.77英寸，最高可达277V交流电压

eCap是一款测量精准、反映迅速的通用电表，适用于高精度应用，可测量电压、电流、功率、能量和频率以及功率因数，并通过集成的Modbus RTU或RS485接口实现完全电隔离传输。

产品发布时间 : 2023-03-10

【产品】TELE推出的紧凑型相位损失监视器E1PF480Y/277VSY01，额定频率48-63Hz，平衡设置可调节

TELE推出的紧凑型和最畅销的相位损失监视器E1PF480Y/277VSY01通常被称为工业面板的保险策略，它提供了一种直观的方式，不仅可以保护电气设备，还可以保护机械设备。

产品发布时间 : 2023-01-31

TELE监控继电器选型表

TELE带来如下参数: ENYA、GAMMA、KAPPA、VEO系列继电器，测量/监测电流、电压、温度、频率、电平等，电压带宽12-240V AC/DC&12-690V AC

产品型号	品类	Functionality	Outputs	Supply Voltage
E1IM10AACL10 230V AC	MONITORING RELAY	Multifunction	1 CO	230V AC

选型表 - TELE 立即选型

News on TELE Grid＆System Protection: Version “I” Available

Version “I” of the grid and system protection is accompanied by an extension of the parameter set document. There are 4 new parameter sets for Austria, Serbia, Ireland and Romania have been added to the European parameter sets.

厂牌及品类发布时间 : 2024-07-27

NA003-M64/NA003.COM-M64 Installation Guide

型号- NA003-M64,2700200,NA003.COM-M64,NA003,270010X,NA003.COM

用户指南 - TELE - 08/2023 PDF 英文下载

TELE器件选型表

TELE提供USB CONVERTER（USB转换器），TRANSDUECER（传感器），TIMER MODULE（定时器模块），REMOTE POTENTIOMETER（远程电位器），POWER MODULE（电源模块），PERFORMANCE SENSOR（性能传感器），FRONT COVER，CURRENT TRANSFORMER（电流互感器），COUPLING BLOCK（连接块），BASE SOCKET（底座插座）和ACTIVE CURRENT TRANSDUECER（有功电流传感器）的参数选型，Outputs：1 CO， 2CO，3 CO，ModBus RTU/RS485和USB-RS485，包装：BOX。

产品型号	品类	Functionality	Outputs	包装	描述
S-USB485	USB CONVERTER	Serial Converter USB-RS485	USB-RS485	BOX	Serial converter USB-RS485 (isolated up to 5kV)

选型表 - TELE 立即选型

eCap Performance Sensor From TELE Haase Helps toSave Energy, High Accuracy Up to 0.01 %

The eCap from TELE Haase is a communication-enabled performance sensor for the accurate measurement of analog values for digital data processing. It transmits the measured data via Modbus to a PLC or via IoT module to the cloud and can be used universally with its flexible functionality. Retrofitted without great effort, the performance sensor collects all relevant digital data for the optimization of machines and systems, and helps customers save energy

厂牌及品类发布时间 : 2023-09-09

270010xH RE - NA003-M64 Grid and System Protection Relay USER MANUAL

型号- NA003-M64,270010XH,NA003

用户指南 - TELE - 2023-02-16 PDF 英文下载

Authorized Use of the c(UL)us Mark for TELE‘s Performance Sensor eCap

TELE‘s Performance Sensor eCap has received the UL certification and is now authorized to use the c(UL)us mark. All tests and evaluations have been completed successfully.

厂牌及品类发布时间 : 2024-04-25

RE - NA003-M64 RE - NA003.COM-M64(*A) Grid and System Protection Relay USERS GUIDE

型号- NA003-M64,270010XH,NA003.COM-M64,NA003,2700200H

用户指南 - TELE - 2023-04-25 PDF 英文下载

TELE Visits HAZET to Optimise the Grid And System Protection NA003

The special feature of the grid and system protection NA003-M64 from TELE is that it combines all standards in one device and can be used universally and internationally.

厂牌及品类发布时间 : 2023-10-12

New firmware version for TELE eCap Performance Sensor

By integrating the Performance Sensor eCap – and thus modern sensor and communication technology – existing systems become communication-capable. To constantly improve TELE products, TELE has revised the software for the eCap (Firmware Updater and eCap Configurator).

厂牌及品类发布时间 : 2023-10-11