Design Method of Analog Switch to Switch Audio Signal
The noise-canceling headphones, speakers, KVM, matrix, mixers, etc often require to processing of multiple audio signals. Designing a set of conditioning circuits for each audio signal will be very expensive and very complicated. The use of Analog switches for interleaving is obviously a very efficient approach.
The following design schemes are commonly used:
●Switching with an analog switch powered by a common single power supply
The signal range that ordinary analog switches can pass is -0.3V~VCC. For switching AC signals such as audio, DC bias voltage should be superimposed, that is, the signal must be raised above zero volts to pass reliably (Fig. 1). Each channel needs to add 3 resistance-capacitance components. If the signal has a DC bias voltage, it can be directly given to the analog switch.
Fig.1 Ordinary switch RS2105 switches audio signals
●Analog switch with dual power supply
The analog switch with dual power supply, including an analog switch with a built-in negative voltage charge pump, the dynamic range of the signal that can be passed is broader, such as 74HC4051, support -VEE~+ VCC signal range, but requires additional components, which will increase the cost significantly.
●Use an analog switch with a negative swing capability
This is a type of analog switch with a negative swing designed specifically for AC signals, such as RS2117 and RS2118. The negative voltage signal that can be delivered under a single power supply can reach a maximum of -2V. Using this type of IC to switch audio signal circuits is the most efficient and cost-effective Higher (Fig. 2).
Fig.2 RS2118 switching audio signal
● With relay
Relay is the best choice for performance with small on-resistance and very good isolation, but they are bulky and expensive.
RS2117/RS2118 is a dual-channel single-pole double-throw (SPDT) analog switch of Runestone Technology. Its main features are as follows:
● -3dB bandwidth: 400MHz/RS2117, 80MHz/RS2118;
● Low on-resistance: 4.0Ω/RS2117, 0.8Ω/RS2118;
● Working voltage range: 2.5V~5.5V;
● Maximum pass signal range: -2V~VCC;
● Ultra-low power consumption:
● High shutdown isolation: -70dB@1MHz;
● High channel isolation: -72dB@1MHz;
● Provide QFN-1.4x1.8-10L small package.
Note: The smaller the on-resistance is, the larger the current that can pass. RS2118 is more suitable for switching with the load.
Fig.3 R2117/RS2118 pin diagram
Special attention needs to be paid to the design. The negative voltage signal range that RS2117/RS2118 can pass is subject to the VCC power supply voltage, that is, the negative voltage that can be passed is VCC-5.5V, the lowest is -2V, such as 3.3V power supply, the signal range It is -2V~3V.
- |
- +1 赞 0
- 收藏
- 评论 0
本文由三年不鸣转载自RUN-IC News，原文标题为:Design method of analog switch to switch audio signal，本站所有转载文章系出于传递更多信息之目的，且明确注明来源，不希望被转载的媒体或个人可与我们联系，我们将立即进行删除处理。
相关推荐
【经验】解析模拟开关应用设计要点及选型步骤
模拟开关，是利用JFET或MOS的特性实现控制信号通路的开关，主要用来完成信号链路连接或断开的切换功能。由于它具有功耗低、速度快、无机械触点、体积小和使用寿命长等特点，在各种自动控制系统和电子数码产品中得到了广泛应用。本文润石科技分享模拟开关的一些基础要点，为广大工程师在模拟开关应用设计和选型使用上提供参考。
【经验】模拟开关切换音频信号的设计方法
在降噪耳机、音箱、KVM、矩阵、调音台等产品上，常常需要对多路的音频信号进行处理，每一路音频信号都设计一组调理单元成本会非常高昂，电路也会非常庞杂。而用模拟开关做分时切换复用，显然是非常便捷的设计思路。本文润石科技来介绍模拟开关切换音频信号的设计方法。
【产品】用于切换音频电路的双通道单刀双掷模拟开关RS2117/RS2118，单电源供电下能过的负压信号可达-2V
RS2117/RS2118是润石科技的双通道单刀双掷（SPDT）模拟开关，是专门为交流信号设计的带负摆幅的开关，其工作电压为2.5V~5.5V，最大通过信号范围为-2V~VCC，具有＜=1uA的超低功耗，提供QFN-1.4×1.8-10L小封装。
润石科技模拟开关选型表
润石科技为客户提供了一系列的低压模拟开关，包含多种信号范围的单通道和多通道模拟开关产品，具有低导通阻抗（低至0.5Ω）、高速、高性能、小封装、选型丰富等特点
|
产品型号
|
品类
|
CH
|
Type
|
RON(@5V)（Ω）
|
-3dB Bandwidth（MHz）
|
VCC（V）
|
Iq（μA）
|
VINH(@5V)（V）
|
tON(@5V)（ns）
|
tOFF(@5V)（ns）
|
|
RS2101
|
模拟开关
|
1
|
1:2
|
3Ω
|
120MHz
|
1.8V~5.5V
|
1μA
|
0.6V~1.5V
|
29ns
|
17ns
|
选型表 - 润石科技 立即选型
切换音频信号用什么芯片？
音频信号如果不带偏置电压，负半周信号就是在0V以下，需要模拟开关支持负摆幅才能用于切换音频信号，RS2117、RS2118最大可以支持-2V的负压信号，可以满足音频信号的切换。
RS2057 4.5Ω低压单刀双掷模拟开关
润石科技 - 低电压单刀双掷模拟开关,LOW VOLTAGE SPDT ANALOG SWITCH,单刀双掷模拟开关,SINGLE-POLE DOUBLE-THROW ANALOG SWITCH,SPDT ANALOG SWITCH,RS2057XH,RS2057,RS2057XC6,便携式计算,模数转换系统,WEARABLE DEVICES,手机,SIGNAL DEMODULATION,BATTERY-OPERATED EQUIPMENT,SIGNAL MODULATION,SIGNAL CHOPPING,CELL PHONES,信号解调,PORTABLE COMPUTING,电池供电设备,数模转换系统,SIGNAL GATING,DIGITAL-TO-ANALOG CONVERSION SYSTEMS,信号调制,ANALOG-TO-DIGITAL CONVERSION SYSTEMS,信号斩波,可穿戴设备,信号选通
【选型】模拟开关选型时需要关注的参数
模拟开关，是利用JFET或MOS的特性实现控制信号通路的开关，主要用来完成信号链路连接或断开的切换功能。由于它具有功耗低、速度快、无机械触点、体积小和使用寿命长等特点，在各种自动控制系统和电子数码产品中得到了广泛应用。本文主要介绍模拟开关选型时需要关注哪些参数，以及润石科技的模拟开关有哪些应用场景。
切换MIC信号用什么开关？
MIC，即咪头，通常输出的音频信号最大只有几百mV，但是会有负压，故最好选用RS2117\RS2118这种音频专用的开关切换。
RS2323超低导通电阻、低电压、双通道、单刀双掷模拟开关
润石科技 - DUAL, LOW ON-RESISTANCE, SINGLE-POLE DOUBLE-THROW ANALOG SWITCH,双通道、低导通电阻、单刀双掷模拟开关,ULTRA-LOW ON-RESISTANCE, LOW VOLTAGE, DUAL, SPDT ANALOG SWITCH,DUAL, LOW ON-RESISTANCE, SPDT ANALOG SWITCH,超低导通电阻、低电压、双通道、单刀双掷模拟开关,RS2323XUTQK10,RS2323,便携式计算,模数转换系统,WEARABLE DEVICES,手机,SIGNAL DEMODULATION,BATTERY-OPERATED EQUIPMENT,SIGNAL MODULATION,SIGNAL CHOPPING,CELL PHONES,信号解调,PORTABLE COMPUTING,调制解调器,电池供电设备,数模转换系统,DIGITAL-TO-ANALOG CONVERSION SYSTEMS,SIGNAL GATING,信号调制,ANALOG-TO-DIGITAL CONVERSION SYSTEMS,信号斩波,可穿戴设备,MODEM,信号选通
RS2252 CMOS两个4通道模拟多路复用器/多路分用器
RS2252是一款由RUNIC Technology Co., Ltd.生产的CMOS模拟集成电路，作为两个4通道多路复用器。该器件可在2.5V至5.5V的单电源下工作，具有低导通电阻（典型值为48Ω）和非常低的漏电流（典型值为1nA）。它支持高断开隔离（-83dB），适用于各种应用，包括传感器、模拟和数字复用/解复用、模数转换、信号门控、电池供电设备、工厂自动化、家用电器和通信电路。
润石科技 - CMOS模拟集成电路,DIGITALLY-CONTROLLED ANALOG SWITCHES,CMOS ANALOG IC,数字控制模拟开关,CMOS双4通道模拟多路复用/解复用器,CMOS TWO 4-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER,RS2252XTSS16,RS2252,RS2252XTQC16,RS2252XSS16,RS2252XS16,FACTORY AUTOMATION,电池供电设备,SIGNAL GATING,APPLIANCES,COMMUNICATIONS CIRCUITS,器具,BATTERY-OPERATED EQUIPMENT,工厂自动化,通信电路,SENSORS,信号选通,传感器
切换CVBS/AHD/CVI等视频信号用什么开关？
复合视频信号同步头会有-300mV的信号，故最好选用RS2117\RS2118这种能过负压的开关切换。
RS2233宽带4通道单刀双掷视频模拟开关
RS2233是一款宽带宽四通道双向单刀双掷（SPDT）视频模拟开关CMOS集成电路。该器件可在1.8V至5.5V的单电源电压下工作，具有低导通电阻、低串扰和高频响应等特点。
润石科技 - CMOS模拟集成电路,DIGITALLY-CONTROLLED ANALOG SWITCHES,CMOS ANALOG IC,数字控制模拟开关,WIDE-BANDWIDTH 4-CHANNEL SPDT VIDEO ANALOG SWITCH,宽带4通道单刀双掷视频模拟开关,RS2233YTSS16,RS2233YSS16,RS2233,RS2233YS16,DVD播放机,视频切换,个人录像机,VIDEO SWITCHING,PERSONAL VIDEO RECORDERS,GAME CONSOLES,防守,HARD DISK RECORDERS,医学应用,游戏控制台,航空航天,DVD PLAYERS,MEDICAL APPLICATIONS,AUDIO SWITCHING,DEFENSE,音频转接,硬盘录像机,AEROSPACE,桌面视频编辑器,DESKTOP VIDEO EDITORS
RS2105超低导通电阻、低电压、双通道、单刀双掷模拟开关
润石科技 - DUAL, LOW ON-RESISTANCE, SINGLE-POLE DOUBLE-THROW ANALOG SWITCH,双通道、低导通电阻、单刀双掷模拟开关,ULTRA-LOW ON-RESISTANCE, LOW VOLTAGE, DUAL, SPDT ANALOG SWITCH,单刀双掷模拟开关,超低导通电阻、低电压、双通道、单刀双掷模拟开关,SPDT ANALOG SWITCH,RS2105,RS2105XTDC10,RS2105XN,便携式计算,模数转换系统,WEARABLE DEVICES,手机,BATTERY-OPERATED EQUIPMENT,CELL PHONES,PORTABLE COMPUTING,调制解调器,电池供电设备,数模转换系统,SIGNAL GATING,DIGITAL-TO-ANALOG CONVERSION SYSTEMS,ANALOG-TO-DIGITAL CONVERSION SYSTEMS,可穿戴设备,MODEM,信号选通
切换I2C接口用什么芯片？
I2C接口的通讯速率目前规范最高是400KHz，对模拟开关的带宽要求并不高，润石所有模拟开关都可以用于I2C信号的切换，比如2选1可以用RS2058、RS2323、RS2117、RS2118、RS2105等，4选1可以用RS2252。
RS2266 4.5Ω双通道双向单刀单掷模拟开关
RS2266是一款双向双通道单刀单掷（SPST）模拟开关，适用于1.8V至5.5V的电压范围。它具有300MHz的带宽和4.5Ω的典型导通电阻，适用于无线设备、音频和视频信号路由、便携式计算和可穿戴设备等应用。
润石科技 - 双向2通道单刀单掷模拟开关,BIDIRECTIONAL 2-CHANNEL SINGLE-POLE SINGLE-THROW ANALOG SWITCH,DUAL BILATERAL SPST ANALOG SWITCH,双向2通道SPST模拟开关,BIDIRECTIONAL 2-CHANNEL SPST ANALOG SWITCH,双路双向单刀单掷模拟开关,RS2266,RS2266XM,RS2266XTDB8-B,模数转换系统,手机,SIGNAL MODULATION,VIDEO SIGNAL ROUTING,调制解调器,SIGNAL GATING,信号调制,无线器件,信号斩波,WIRELESS DEVICES,便携式计算,WEARABLE DEVICES,SIGNAL DEMODULATION,SIGNAL CHOPPING,CELL PHONES,信号解调,PORTABLE COMPUTING,音频信号路由,AUDIO SIGNAL ROUTING,数模转换系统,DIGITAL-TO-ANALOG CONVERSION SYSTEMS,ANALOG-TO-DIGITAL CONVERSION SYSTEMS,可穿戴设备,MODEM,信号选通,视频信号路由
电子商城
现货市场
授权代理品牌：集成电路
授权代理品牌：分立元件
授权代理品牌：接插件及结构件
授权代理品牌：部件、组件及配件
授权代理品牌：电源及模块
授权代理品牌：电子材料
授权代理品牌：仪器仪表及测试配组件
授权代理品牌：电工工具及材料
授权代理品牌：机械电子元件
授权代理品牌：加工与定制
我要提问
登录 | 立即注册
提交评论