Technical Standards for Fuses

时间： 2023-11-28 来源：XC News

技术问答

选型帮助

研发客服

商务客服

1. Rated zero power resistance

PPTC thermistors should be packaged according to zero power resistance levels, and the resistance range should be indicated on the outer packaging. After the withstand voltage and current resistance tests, the change rate of the resistance before each group of samples is extremely poor δ| After Ri - Before Ri - (After Rj - Before Rj)/Before Rj | ≤ 100%.

2. PTC effect

A material has a PTC (Positive Temperature Coefficient) effect, which means that the resistance of the material increases with increasing temperature. Most metal materials have the PTC effect. In these materials, the PTC effect is manifested as a linear increase in resistance with increasing temperature, which is commonly referred to as the linear PTC effect.

3. Nonlinear PTC effect

The material undergoing phase transformation will exhibit a phenomenon where the resistance rapidly increases by several to more than ten orders of magnitude along a narrow temperature range, known as the nonlinear PTC effect. Various types of conductive polymers exhibit this effect, such as polymer PTC thermistors. These conductive polymers are very useful for manufacturing overcurrent protection devices.

4. Initial resistance Rmin

Before being installed in the circuit, test the resistance value of the polymer PTC thermistor of the self resetting fuse series at an ambient temperature of 25℃.

5. Rmax

Under room temperature conditions, the self resetting fuse series polymer PTC thermistor acts or reflows.

The maximum resistance value is measured after one hour of installation in the circuit board.

6. Minimum resistance (Rmin)/maximum resistance (Rmax)

At a specified ambient temperature, such as 25℃, the resistance value of a specific model of self resetting fuse series polymer thermistor before installation in the circuit will be within a specified range, that is, between the minimum value (Rmin) and the maximum value (Rmax). This value is listed in the resistance column of the specification.

Fig.1

发送到邮箱 |
+1 赞 0
收藏
评论 0
| 转发至：

本文由三年不鸣转载自XC News，原文标题为:fast blow or slow blow fuse for amplifier.Technical standards for fuses，本站所有转载文章系出于传递更多信息之目的，且明确注明来源，不希望被转载的媒体或个人可与我们联系，我们将立即进行删除处理。

全部评论（0）

暂无评论

The Impact of Fuse Aging on Usage

After the fuse ages, there is no danger of generating the current that should be cut off and the fuse not blowing. The aging of a fuse is equivalent to a decrease in the rated value (current) rather than an increase, resulting in the circuit being cut off at a small overload current or pulse.

技术探讨发布时间 : 2023-12-16

Encapsulation Forms of Current Fuses

The encapsulation of current fuses is an important aspect that affects their performance, durability, and safety.

技术探讨发布时间 : 2024-11-13

Explanation of Parameters in the PPTC Specification for Self Healing Fuses

This is very simple. As long as you know the meaning represented by the parameters in the specification book, you can clearly and quickly view the PTC specification book for self recovery fuses.

技术探讨发布时间 : 2024-08-21

旭程（XC）保险丝选型指南

目录- Company Profile Fuse User's Manual Fuse Auto Fuse Fuse Holder Thermostat

型号- 06F,3S,C0015302Z,C0040302Z,3T,10C,06T,C0060303Z,4F,KSD9700,C0030301Z,6CH,C7500301Z,4T,C0015301Z,C0070303Z,4TE,C0040303Z,8TE,C0025302Z,5C,KSD305,5F,5G,C4000302Z,5H,9L,KSD301,C2000302Z,C0030302Z,10FV,C0020301Z,5S,C7500302Z,5T,C0010302Z,24F,12F,32F,C0080303Z,5SH,6B,6C,C0025301Z,6F,6G,24T,6H,12T,C3000301Z,C4000301Z,C5000301Z,2F,C2000301Z,C0030303Z,32T,R3-13,5GH,R3-12,R3-11,5CH,6S,C0020302Z,6T,2T,5TE,XC-1,BS1362,C0010301Z,C3000302Z,5TR,3F,3G,C5000302Z,C1000302Z,XC-2,C0050303Z,C0035302Z,C0020303Z

选型指南 - 旭程 - Ver.1.0 - 2022/2/16 PDF 英文下载

Calculation Method for Melt Current of Fuse Fuses

The current of a fuse includes two aspects, one is the rated current of the fuse tube, and the other is the rated current of the melt, which cannot be confused.

设计经验发布时间 : 2023-11-24

Several Factors Influence the Lifetime of Current Fuses

The lifetime of a current fuse is influenced by several factors. Firstly, the current rating of the fuse plays a crucial role. If a fuse is constantly operating near or at its rated current, it will experience more heat buildup and stress over time, which can shorten its lifetime.

技术探讨发布时间 : 2024-11-06

Professional Knowledge of Self-healing Fuses

The operating principle of a self-healing fuse is a dynamic balance of energy. The current flowing through the self-healing fuse generates a certain amount of heat due to the thermal effect of the current (self-healing fuses all have resistance values), and the generated heat is completely or partially dissipated into the environment. The heat that is not dissipated will increase the temperature of the self-healing fuse components. The temperature during normal operation is relatively low, and the heat generated and dissipated reaches a balance.

技术探讨发布时间 : 2023-11-30

SMD fuse and Chip Fuse Specifications

SMD fuses can be divided into SMD disposable fuses and SMD self recovery fuses. Among them, the specifications of patch disposable fuses include series 060312062410 fuses, and the specifications and dimensions of patch self recovery fuses include series 0603, 0805, 1206, 1210, 1812, 2920, etc.

技术探讨发布时间 : 2023-12-04

The Installation Precautions for Current Fuses

The installation of current fuses is crucial for ensuring the safety and proper functioning of electrical circuits. Here are some important installation precautions to keep in mind.

设计经验发布时间 : 2024-11-04

Self Recovery Performance and Working Process of Self Recovery Fuses

Traditional fuses are installed in circuits. When an overcurrent occurs due to a fault or abnormality in the circuit, the fuse itself melts to cut off the current and protect the circuit. However, due to the fact that traditional fuses can only protect once and need to be replaced if burned out, some products still cannot resume operation after troubleshooting or abnormal overcurrent disappears. As a new type of overcurrent protection device, the self-recovery fuse has the function of automatic recovery, which can meet the performance requirements of similar applications.

技术探讨发布时间 : 2023-12-15

Solution to Fuse Failure

XC shares about Solution to Fuse Failure.

设计经验发布时间 : 2023-12-29

Guide to Current Fuse Selection

Selecting the appropriate current fuse is crucial for the safety and efficient operation of an electrical system. Firstly, one must consider the rated current of the circuit. The rated current of the fuse should be slightly higher than the normal operating current of the circuit. For example, if a circuit typically operates at 5 amperes, a fuse with a rated current of around 5 - 7 amperes might be suitable. However, it should not be too high, as this may lead to a situation where the fuse does not blow when it should during an overload or short - circuit.

器件选型发布时间 : 2024-10-16

5TE 系列 12A/300方型塑胶保险丝（环保产品）产品承认书（5TE SERIES 12A/300V 5TE SUB-MINIATURE FUSE-LINK(GREEN PRODUCT) SPECIFICATION FOR APPROVAL）

型号- 5TE,5TE SERIES,5TE 系列,011.212060001

数据手册 - 旭程 - 版本1.0（REV.1.0） - 23.9.7 PDF 中英文下载

What is A Self Recovery Fuse

Self recovery fuse is an overcurrent electronic protection component that uses a polymer organic polymer under high pressure, high temperature, and sulfurization reaction conditions.After mixing with conductive particle materials, it is processed through a special process. Habitually applying PPTC (Polymer Positive Temperature).

设计经验发布时间 : 2023-12-05

Introduction of Surface Mount Fuses

Surface mount fuse is a widely used protective component in electronic circuits. Patch fuses are compact in size and typically flat in shape. This compact structure gives it a unique advantage in the trend of miniaturization in modern electronic devices, effectively saving space on circuit boards.

技术探讨发布时间 : 2024-09-26