Four Points to Control the PCB Cost: PCB Layers, PCB Dimensions, Manufacturing Difficulty and PCB Sheet Material

时间： 2023-12-19 来源：SIFU News

Usually in the case of the same area, the more layers of PCB, the more expensive the price. Design engineers should use as few layers as possible to complete the PCB design while ensuring the quality of the design signal.

In the PCB design, the factors that affect the cost mainly include the following four points.

PCB Layers

In the case of the same area, the more PCB layers, the more expensive the price. Design engineers should use as few layers as possible to complete the PCB design while ensuring the quality of the design signal.

PCB Dimensions

In the case of a certain number of layers, the smaller the size of the PCB, the lower the price. If the design engineer can reduce the size of the PCB without affecting the electrical performance in the PCB design, the size and cost can be reduced reasonably.

Manufacturing Difficulty

The main parameters affecting PCB manufacturing are small line width, small line spacing, small drilling holes, etc. If these parameters are set too small or the process capability has reached the small limit of the PCB factory, the yield of the PCB will be low. , the cost of manufacturing will increase. Therefore, in the process of designing the PCB, try to avoid challenging the limits of the factory, set a reasonable line width and line spacing, and drill holes. In the same way, through holes can complete the design, try not to use the blind and buried holes of HDI, because the processing technology of blind and buried holes is much more difficult than that of through holes, which will increase the cost of PCB production.

PCB Sheet Material

There are many classifications of PCB sheets, such as common paper-based printed circuit boards, epoxy glass fiber cloth printed circuit printed circuit boards, composite substrate printed circuit boards, special substrate printed circuit boards, metal substrates, etc. There is a big difference in the processing of different materials, and the processing cycle of some special materials will be longer. Therefore, in the design, try to choose cheap materials that can meet the design requirements and are more common, such as RF4 materials.

发送到邮箱 |
+1 赞 0
收藏
评论 0
| 转发至：

本文由上山打老虎转载自SIFU News，原文标题为:To control the cost of PCB, you have to look at these four points，本站所有转载文章系出于传递更多信息之目的，且明确注明来源，不希望被转载的媒体或个人可与我们联系，我们将立即进行删除处理。

全部评论（0）

暂无评论

PCB多层板为什么很少有奇数层？

PCB板有双面PCB、四层PCB、六层PCB、八层PCB等,目前已经有超过100层的PCB，那为何大家会有“PCB多层板为什么都是偶数层？”这种疑问呢？相对来说,偶数层的PCB确实要多于奇数层的PCB。

2023-12-30 - 技术探讨

Price and Cost of Circuit Boards

According to the design of the circuit board, the price will vary depending on the material of the circuit board, the number of layers of the circuit board, the size of the circuit board, the quantity of each production, the production process, the small line width and line spacing, the small hole diameter and the number of holes , special process requirements to decide.

2024-11-30 - 技术探讨

HDI PCB板常用的叠层结构介绍

叠层结构是影响PCB板EMC性能的一个重要因素，也是抑制电磁干扰的一个重要手段。随着高速电路的不断涌现，PCB板的复杂度也越来越高，为了避免电气因素的干扰，信号层和电源层必须分离，所以就牵涉到HDI PCB板叠层设计。那么，HDI PCB板常用的叠层结构都有哪些？本文中赛孚将为大家详细介绍。

2023-12-21 - 技术探讨

深圳市赛孚（SIFU）电路科技有限公司成立于2011年，公司由多名电路板行业的专家级人士创建，是国内专业的PCB/FPC快件服务商之一。公司成立以来，一直专注样品，中小批量领域。快速的交付以及过硬的产品品质赢得了国内外客户的信任。公司是广东电路板行业协会会员企业，是深圳高新技术认证企业。

PCB 软硬结合板高多层PCB HDI PCB 高频高速PCB FPC PCBA

线上商城技术资料

怎么区别HDI PCB一阶和二阶和三阶？

我们经常说的4层一阶HDI，6层二阶HDI，8层3阶HDI，那么怎么区别HDI PCB一阶和二阶和三阶呢？本文进行介绍。一阶的比较简单，流程和工艺都好控制。

2023-12-30 - 设计经验

Super Complete PCB Failure Analysis Technology

As the carrier of various components and the hub of circuit signal transmission, PCB has become an important and critical part of electronic information products. Its quality and reliability level determine the quality and reliability of the entire equipment.

2024-11-30 - 设计经验