For Applications Where the LDO Voltage Regulator Operates Mostly Under No Load Conditions, the Quiescent Current Plays a Major Role
A low dropout LDO voltage regulator is a linear device that maintains a stable output over a wide range of input voltages and output currents. LDOs operate at low voltage differences between input and output. Furthermore, they can be used as noise reduction patches to solve voltage regulation problems caused by electromagnetic interference (EMI) and printed circuit board (PCB) routing. Luckily, the enable function allows switching the regulator on and off, thus improving the overall system efficiency by turning off unused functions.
Enabling
The Enable input (EN), available in positive and negative logic, turns the device on and off by an external signal. Active-high logic activates the device when the voltage at the EN-input exceeds the high-logic threshold. The active-low logic switches the device off when the EN-voltage falls below the logic low threshold. The EN-function is an important feature when sequencing power supplies in multi-rail systems. Keeping the internal bandgap reference running while the regulator is disabled allows for fast turn-on times.
Figure 1: DIOTEC LDI8119-xxEN internal block diagram
Shutdown-Current and Quiescent current
When the LDO is turned off and connected to the battery system, the input current will be limited, usually up to 1 μA. This Shutdown current is commonly confused with the quiescent current which is the current drawn by the device when it is enabled and operating with no load. Both shutdown and quiescent current are important parameters when realizing long battery lifetimes in portable devices. Using the datasheet values for shutdown and quiescent current designers can calculate power dissipation as shown in the below equations.
For example, when the device is fully operational, the voltage is regulated from VIN 10.0 V to VOUT 5.0 V with an output current of 400 mA. The datasheet value for quiescent current is 60 μA. This will result in a power dissipation (PD) of:
Check again with new value for IQ
PD= (VIN-VOUT ) ∙ IOUT + (VIN ∙ IQ )
PD= (10 V - 5 V) ∙ 0.4 A + (10 V ∙ 0.00006 A)
PD= 2.0006 W
When the device is switched into no load operation, the output current falls as low as 200
μA. Then the PD becomes:
PD= (10 V-5 V) ∙ 0.0002 A + (10 V ∙ 0.00006 A)
PD= 1.6 mW
In this case, the quiescent current accounts for nearly 50% of the total power dissipation.In conclusion, the following is stated: For applications where the device operates mostly under no load conditions, the quiescent current plays a major role and should be considered when planning the design.
- |
- +1 赞 0
- 收藏
- 评论 0
本文由电子人生转载自Diotec,原文标题为:LDO Voltage Regulator with Enable Function and Low IQ,本站所有转载文章系出于传递更多信息之目的,且明确注明来源,不希望被转载的媒体或个人可与我们联系,我们将立即进行删除处理。
相关推荐
Diotec Ultrafast Rectifier US1M——Why It Makes Sense to Use a 1000 V Component on a 24 V Smart Building Field Bus System?
The 1000V of the Diotec US1M provides sufficient protection for reliable and long lasting smart building functionality.
德欧泰克超低压差稳压器LDI55-ADEEN用于便携式音箱,高输出电流和关断功能助力随时随地享受音乐
无论你是在度假、开会还是和朋友们在户外,这些小巧的便携式音箱都能随时随地发出美妙的音质。不管它的大小和价格如何,一款优质的蓝牙音箱应该提供两位数的电池续航能力。DIOTEC的ESOP-8封装中配备了超低压差稳压器,具有高输出电流和关断功能,可调至300mA,同时具有热过载保护和非常低的静态电流。
Diotec(德欧泰克)稳压器选型指南
目录- Regulators
型号- DI62063.6S1,DI62063.6S2,DI78L08DAB,DI78L15ZAB,DI78L18ZAB,DI62062.8S1,DI62062.8S2,DI79L08ZAB,LDI812C-3.3SFA,LDI1117-1.5H,DI78L24ZAB,LDI1117-1.5D,DI78L09ZAB,DI79L10DAB,DI78L12ZAB,DI78L05DAB,DI78L3.3DAB,MMTV431A,DI78L08UAB,DI79L05UAB,MMTV4041,DI78L06ZAB,DI62063.3S2,LDI1117-1.8D,DI78L12DAB,DI78L06DAB,DI79L06ZAB,DI79L05DAB,DI79L08UAB,DI62062.5S1,DI62062.5S2,DI78L15UAB,DI78L09UAB,DI79L15ZAB,DI62063.3S1,DI79L08DAB,LDI1117-05H,LDI1117-05D,DI78L10ZAB,DI78M05UAB,LDI1117-2.5U,LDI1117-1.8U,DI78L12UAB,DI79L12ZAB,DI79L09ZAB,LDI1117-05U,DI78L06UAB,LDI1117-2.5H,LDI1117-1.8H,LDI1117-2.5D,LDI1117-ADH,DI78L05ZAB,LDI1117-ADD,DI79L15UAB,LDI1117-3.3U,DI78L3.3ZAB,DI79L06UAB,LDI1117-ADU,LDI1117-3.3H,DI79L12DAB,LDI1117-3.3D,DI62063.0S1,DI62063.0S2,MMTL431A,DI78L09DAB,DI78L15DAB,DI79L24ZAB,DI79L18ZAB,MMTL431AR,DI78L10UAB,DI79L06DAB,LDI75L3.3UA,DI79L09UAB,LDI812C-3.3UA,DI79L12UAB,DI79L10ZAB,LDI1117-1.2H,LDI1117-1.2D,DI78L3.3UAB,DI78L24UAB,DI78L18UAB,LDI1U7-1.2U,DI79L24DAB,DI79L09DAB,LDI75L05UA,DI78L05UAB,DI79L18DAB,DI62061.8S2,DI62061.8S1,DI79L05ZAB,LDIU17-1.5U,DI79L18UAB,DI78L24DAB,DI79L10UAB,DI78L18DAB,DI79L15DAB,DI78L10DAB,DI79L24UAB,DI78L08ZAB
低压差稳压器LDI8119-3.3EN为空气质量控制测量单元供电,提供高输出电流与关断功能
DIOTEC的LDI8119-3.3EN是一款低压差稳压器,用于恒定直流电压调节和过压保护。采用SOT-23-5封装,并提供高输出电流与关断功能。在多种实际应用中,如空气质量传感器、智能/燃气表、电池备用稳压电源和电表,它提供3.3V输出,+/-1%的j精度,最大输出电流可达500mA。
Ultra Low Power LDO Designed for Low-Power Electronics and Battery Operated Systems | Diotec
The LDI812C-3.3SFA from Diotec is a CMOS based high voltage low-dropout positive voltage regulator, specifically designed for low-power electronics and battery operated systems where power savings are decisive. This device can be operated at a wide range of input voltage up to 16 V. It features a fixed output voltage of 3.3 V and output current rating of 50 mA. Dropout voltage is as low as 230 mV and quiescent current ultra-low at typically 1 µA.
【应用】正固定电压稳压器LDI8233-3.3EN用于微控制器供电,实现无绳修剪树篱
Diotec正固定电压稳压器LDI8233-3.3EN可为微控制器供电,提供高达40V的输入电压、100mA的输出电流和热过载保护。在不使用的情况下,可利用启用功能关闭整个控制电路,有助于延长电池待机时间。适合于任何电池供电的花园设备。
Portable and Waterproof Speakers – Supplied By the Adjustable LDO LDI55-ADEEN with Enable Pin
The LDI55-ADEEN linear voltage regulator from Diotec is an adjustable low dropout voltage regulator (LDO) that delivers an output voltage between 1.3 and 15 V with a tolerance of +/- 2% and a very low dropout voltage. It is a perfect match to supply portable devices like a waterproof outdoor speaker.
Battery Management Systems (BMS) APPLICATION NOTE
型号- BZT52C2V0-AQ,DI110N06D1-AQ,LDI8233-05EN,MMFTN620KDW-AQ,SK84-AQ,NUP2105L-AQ,NUP3105L-AQ,P4SMAJ85CA-AQ,BZX84C47-AQ,DI080N06PQ-AQ 8,5.0SMCJ58CA-AQ,SK36SMA-AQ,MM3Z39-AQ,LDI8233-3.3EN,ESDB24C-AQ,2BZX84C3V3-AQ,SK3H15SMB-AQ,5.0SMCJ12A-AQ,BZX84C2V7-AQ,LDP02-26AYD2-AQ,2BZX84C27-AQ,MM3Z2V7-AQ,LDI812C-3.3UA,BZT52C75-AQ,P4SMAJ10A-AQ,ESD9BL0521P-Q,DI110N04PQ-AQ,LDP02-68AYD2-AQ
DIOTEC Linear Voltage Regulator选型表
DIOTEC Linear Voltage Regulator线性电压调节器 提供以下参数选型: Input Voltage Vin[V]:-39~40、Output Voltage VOUTmin[V]:-23~23、Output Voltage VOUTmax[V]:-25~25、Junction Temperature Tjmax [℃]:85~150、Quiescent Current IQ[mA]:0.0001~6.5、Dropout Voltage VD[V]:0.06~2、Output Current IO[A]:0.05~1
产品型号
|
品类
|
Type
|
Package
|
Input Voltage Vin[V]
|
Output Voltage VOUTmin[V]
|
Output Voltage VOUTmax[V]
|
Junction Temperature Tjmax [℃]
|
Quiescent Current IQ[mA]
|
Dropout Voltage VD[V]
|
Output Current IO[A]
|
DI62061.8S1
|
Linear Voltage Regulator
|
SMD
|
SOT-23
|
7
|
1.782
|
1.818
|
85
|
0.008
|
0.39
|
0.08
|
选型表 - DIOTEC 立即选型
Headset with Diotec’s Voltage Regulator LDI8119-05EN Brings an Immersive Acoustic Gaming Experience
Diotec’s Voltage Regulator LDI8119-05EN Series, with a fixed output voltage of 1.8 V to 5.0 V and an output current of 500 mA, provides an efficient and stable reference voltage to the circuit. Typical applications include all kinds of wireless battery-powered devices such as gaming headsets, computer mice, keyboards, and more.
Portable Speakers in Different Designs: Bringing the Music on the Go with Diotec‘s LDI55-ADEEN Voltage Regulator
The LDI55-ADEEN from Diotec is an adjustable low dropout (LDO) voltage regulator providing output voltage up to 15V with +/- 2% tolerance at up to 1000 mA of output current. It is assembled in an ESOP-8 case outline and offers an integrated heat pad, very low drop-out voltage, Low quiescent current with thermal overload, and short circuit protection to avoid damage to the part.
LDI8233-3.3EN...LDI8233-05EN Low Dropout Positive Fixed Voltage Regulators
型号- LDI8233-3.6EN,LDI8233-05EN,LDI8233-3.3EN
LDI8119xxEN Low Dropout Positive Fixed Voltage Regulators
型号- LDI8119-2.5EN,LDI8119-3.3EN,LDI8119XXEN,LDI8119-05EN
Cordless Hedge Trimmer can be Done Via Diotec‘s Positive Fixed Voltage Regulator LDI8233-3.3EN
Now, cordless types are very popular and garden lovers benefit from a higher flexibility and less effort when trimming. The supply for the microcontroller can be done via our Positive Fixed Voltage Regulator LDI8233-3.3EN, they are ideally suited for any battery powered garden device.
【产品】德欧泰克稳压器LDI8119-05EN,静态电流1.8μA,可为无线游戏耳机提供稳定基准电压
DIOTEC的稳压器LDI8119-05EN系列具有1.8V至5.0V的固定输出电压和500mA的输出电流,为电路提供高效和稳定的基准电压。它还具有EN功能,可以设置其启动或关闭状态,有助于延长电池寿命。该器件的典型静态电流为1.8μA,可降低运作的功率损耗。
电子商城
服务
可定制无线位移传感器量程范围10~600mm,采用了无线传输方式,可远程自动实时检(监)测位移量值,准确度级别(级):0.2、0.5;内置模块:无线传输模块、供电模块;传输距离L(m):可视距离1000 (Zigbee、 LORA)。
最小起订量: 1pcs 提交需求>
配备KEYSIGHT网络分析仪,可测量无线充电系统发射机/接收机线圈的阻抗,电感L、电阻R、电感C以及品质因数Q,仿真不同充电负载阻抗下的无线充电传输效率。支持到场/视频直播测试,资深专家全程指导。
实验室地址: 深圳 提交需求>
登录 | 立即注册
提交评论